¶ Parts List
- Enclosure Cable × 1
- LED Strip Cord × 1
- Hall Switch Cord × 1
¶ Procedures
- Identify two short beams (without any LED strips) and attach four profile connectors to both ends of the beams.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 12 | 4 | H3.0 |
Profiles rank by length: long beam > short beam > column.
Make sure the alignment tabs of the profile connectors are inside the profile grooves. You need to pay attention to this detail also in subsequent similar steps.
- Attach the four columns to the profile connectors.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 12 | 4 | H3.0 |
- Identify the long beam-3 (with the Enclosure converter) and attach it to the profile connectors.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 30 | 4 | H3.0 |
Make sure the inside of all profile connectors faces inward.
- Identify the long beam-1 (with the air inlet) and attach it to the profile connectors.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 30 | 4 | H3.0 |
- Insert one of the front/back panels, the left side panel, and the right side panel into the frame.
Make sure the opening for the exhaust fan is positioned near the back panel with the snap bushing opening located beneath.
Make sure the edges of all panels are inserted into the grooves of the corresponding profiles. You need to pay attention to this detail also in subsequent similar steps.
- Identify two short beams (with LED strips) and attach four profile connectors to both ends of the beams.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 12 | 4 | H3.0 |
- Attach the short beams (with LED strips) installed with the profile connectors to the columns.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 12 | 4 | H3.0 |
Make sure the inside of all profile connectors faces inward.
- Identify the long beam-4 (with the hinges) and attach it to the profile connectors.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 30 | 4 | H3.0 |
Make sure the screw holes of the hinges on the long beam-4 face upward.
- Insert the LED strip cord into the socket of the left LED strip and the 2-pin socket on the left side of the Enclosure converter, and tuck the cord into the gap between the left-rear column and the left side panel.
- Insert the eight sealing plugs into the outer side of all profile connectors.
- Rotate the frame 180° horizontally, then cut out 4 appropriately-sized sealing strips and press them respectively into the outer gaps between profiles and the back panel.
Make sure to install the sealing strips correctly.
You can use the hex key to press the sealing strips.
- Attach the snap bushing to the right side panel.
- Attach the exhaust fan guard, the exhaust fan, and the hose connector to the right side panel.
| Screw | Number | Screwdriver |
|---|---|---|
| M4 × 40 & Wing Nut | 4 | H2.5 |
- Insert the exhaust fan cord into the middle socket on the left side of the Enclosure converter, and secure it with the cable clip.
- Put the hose into the hose clamp and secure the hose to the hose connector.
- Insert the Enclosure cable into the right side of the Enclosure converter and thread the cable through the snap bushing from the inside out.
- Take out the hall switch cord and insert it into the 4-pin socket on the left side of the Enclosure converter.
Cords rank by length: hall switch cord > LED strip cord.
- Insert the hall switch cord into the gap between the left-front column and the left-bottom short beam and the panels, then secure it with the cable clip.
- Move the X axis to the indicated position to prevent collision between the toolhead and other parts of the machine during the process of moving the machine into the Enclosure.
Take care to avoid injury from sharp edges of the steel strip.
Do not press the steel strip.
- Move the machine into the Enclosure.
Make sure the machine does not collide with the Enclosure while moving. It is recommended that at least two people operate together.
- Thread the toolhead cable, the air tube, and the three linear module cables through the snap bushing from the inside out.
- Move the X axis to its maximum forward position, then adjust the position of the Y axes to ensure that the Y axes are aligned with each other.
The axes of the machine are likely to slide when moved into the Enclosure. Please ensure that the Y axis is aligned with each other.
- Insert the last panel into the frame as the front panel.
- Insert the other end of the Hall switch line into the Hall switch of the long beam-2 (with the hall switch).
- Identify the long beam-2 and attach it to the profile connectors. Then, secure the hall switch cord with the cable clip.
| Screw | Number | Screwdriver |
|---|---|---|
| M5 × 30 | 4 | H3.0 |
Make sure the "UP" word in the label faces upward.
- Connect the left and right LED strips with the LED strip cord tucked inside the groove of the long beam-2.
- Cut out 12 appropriately-sized sealing strips and press them respectively into the outer gaps between profiles and the remaining panels.
You can use the hex key to press the sealing strips.
- Attach the Enclosure door and complete the Enclosure assembly.
| Screw | Number | Screwdriver |
|---|---|---|
| M4 × 12 | 4 | H2.5 |
¶ Connecting the Enclosure to Ray
Inserted the Enclosure cable into the Enclosure socket of the integrated controller, as illustrated.
